ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法—標準名稱

ASTM D1243 Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers

ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法

ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法—適用范圍

Scope：

This test method covers the determination of the dilute solution viscosity of vinyl chloride polymers in cyclohexanone. The viscosity is expressed in terms of inherent viscosity (logarithmic viscosity number). The test method is limited to those materials that give clear, uniform solutions at the test dilution.

ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法—引用文件

ASTM D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

ASTM D446 Specifications and Operating Instructions for Glass Capillary Kinematic Viscometers

ASTM D883 Terminology Relating to Plastics

ASTM D1600 Terminology forAbbreviated Terms Relating to Plastics

ASTM D1755 Specification for Poly(Vinyl Chloride) Resins

ASTM D2857 Practice for Dilute Solution Viscosity of Polymers

ASTM E2251 Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids

ISO 1628-2 Determination of Viscosity Number and Limiting Viscosity Number—Part 2: Poly (Vinyl Chloride) Resins

C-434 Testing of Glass Volumetric Apparatus

ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法—相關標準

ISO 1628-2塑料.粘度數和特性粘度數的測定.第2部分:聚(氯乙烯)樹脂/Plastics; determination of viscosity number and limiting viscosity number; part 2: poly(vinyl chloride) resins

GB/T 3401用毛細管黏度計測定聚氯乙烯樹脂稀溶液的黏度/Determination of the viscosity of Poly(vinyl chloride) resins in dilute solution using capillary viscometers

ASTM D1243氯乙烯聚合物的稀溶液粘度的標準試驗方法/Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers

HG/T 2234聚碳酸脂稀溶液粘數的測定方法

ISO 1628-4塑料 用毛細管粘度計測定稀溶液中聚合物的粘度 第4部分:聚碳酸酯(PC)模塑和擠塑材料/Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 4: Polycarbonate (PC) moulding and extrusion materials