ASTM E1602 Standard Guide for Construction of Solid Fuel Burning Masonry Heaters
ASTM E1602用感應耦合等離子體原子發射光譜法(ICP-AES),火焰原子吸收光譜法(FAAS)或石墨爐原子吸收光譜技術(GFAAS)測定鉛含量的標準試驗方法
This guide can be used by code officials, architects, and other interested parties to evaluate the design and construction of masonry heaters. It is not restricted to a specific method of construction, nor does it provide all specific details of construction of a masonry heater. This guide does provide the principles to be followed for the safe construction of masonry heaters.
This guide is not intended as a complete set of directions for construction of masonry heaters.
Construction of masonry heaters is complex, and in order to ensure their safety and performance, construction shall be done by or under the supervision of a skilled and experienced masonry heater builder.
1. Scope
1.1 This guide covers the design and construction of solid fuel burning masonry heaters. It provides dimensions for site constructed masonry heater components and clearances that have been derived by experience and found to be consistent with the safe installation of those masonry heaters.
1.2 Values given in SI units are to be regarded as standard. Inch/pound units may be rounded (see ). All dimensions are nominal unless specifically stated otherwise. All clearances listed in this guide are actual dimensions.
1.3 This guide applies to the design and construction of masonry heaters built on-site with the components and materials specified herein. It does not apply to the construction/installation requirements for component systems that have been safety tested and listed. The requirements for listed masonry heater systems are specified in the manufacturer's installation instructions.
1.4 The design and construction of solid fuel burning masonry heaters shall comply with applicable building codes.
2. Referenced Documents (purchase separately)
ASTM Standards
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C43 Terminology of Structural Clay Products
C71 Terminology Relating to Refractories
C270 Specification for Mortar for Unit Masonry
C401 Classification of Alumina and Alumina-Silicate Castable Refractories
E136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C
UL Standards
UL103 Chimneys, Factory Built Residential Type and Building Heating Appliances
Index Terms
brick; Contraflow; firebrick; fire clay mortar; Grundofen; Kachelofen; Kakelugn; masonry heater; mortar; refractory mortar; Russian; soapstone refractory mortar; Solid fuel-burning masonry heaters; Construction; Contraflow; Brick; Firebrick; Fire clay mortar; Grundofen; Kachelofen/Kakelugn; Masonry heater; Mortar; Refractory mortar; Russian; Soapstone refractory mortar;
ASTM E1602用感應耦合等離子體原子發射光譜法(ICP-AES),火焰原子吸收光譜法(FAAS)或石墨爐原子吸收光譜技術(GFAAS)測定鉛含量的標準試驗方法
This guide can be used by code officials, architects, and other interested parties to evaluate the design and construction of masonry heaters. It is not restricted to a specific method of construction, nor does it provide all specific details of construction of a masonry heater. This guide does provide the principles to be followed for the safe construction of masonry heaters.
This guide is not intended as a complete set of directions for construction of masonry heaters.
Construction of masonry heaters is complex, and in order to ensure their safety and performance, construction shall be done by or under the supervision of a skilled and experienced masonry heater builder.
1. Scope
1.1 This guide covers the design and construction of solid fuel burning masonry heaters. It provides dimensions for site constructed masonry heater components and clearances that have been derived by experience and found to be consistent with the safe installation of those masonry heaters.
1.2 Values given in SI units are to be regarded as standard. Inch/pound units may be rounded (see ). All dimensions are nominal unless specifically stated otherwise. All clearances listed in this guide are actual dimensions.
1.3 This guide applies to the design and construction of masonry heaters built on-site with the components and materials specified herein. It does not apply to the construction/installation requirements for component systems that have been safety tested and listed. The requirements for listed masonry heater systems are specified in the manufacturer's installation instructions.
1.4 The design and construction of solid fuel burning masonry heaters shall comply with applicable building codes.
2. Referenced Documents (purchase separately)
ASTM Standards
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C43 Terminology of Structural Clay Products
C71 Terminology Relating to Refractories
C270 Specification for Mortar for Unit Masonry
C401 Classification of Alumina and Alumina-Silicate Castable Refractories
E136 Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C
UL Standards
UL103 Chimneys, Factory Built Residential Type and Building Heating Appliances
Index Terms
brick; Contraflow; firebrick; fire clay mortar; Grundofen; Kachelofen; Kakelugn; masonry heater; mortar; refractory mortar; Russian; soapstone refractory mortar; Solid fuel-burning masonry heaters; Construction; Contraflow; Brick; Firebrick; Fire clay mortar; Grundofen; Kachelofen/Kakelugn; Masonry heater; Mortar; Refractory mortar; Russian; Soapstone refractory mortar;
