ASTM F914 Standard Test Method for Acoustic Emission for Aerial Personnel Devices Without Supplemental Load Handling Attachments
ASTM F914無附加載荷調節裝置的航空人員隔音和不隔音裝置用聲發射的標準試驗方法
This test method provides a means of evaluating acoustic emissions generated by the rapid release of energy from localized sources within an aerial personnel device under controlled loading. The resultant energy releases occur during intentional application of a controlled predetermined load. These energy releases can be monitored and interpreted by qualified individuals.
This test method permits testing of the major components of an aerial personnel device under controlled loading. This test method utilizes objective criteria for evaluation and may be discontinued at any time to investigate a particular area of concern or prevent a fault from continuing to ultimate failure.
This test method provides a means of detecting acoustic emission sources that may be defects or irregularities, or both, affecting the structural integrity or intended use of the aerial personnel device.
Sources of acoustic emission found with this test method shall be evaluated by either more refined acoustic emission test methods or other nondestructive techniques (visual, liquid penetrant, radiography, ultrasonics, magnetic particle, etc.). Other nondestructive tests may be required to locate defects present in aerial personnel devices.
Defective areas found in aerial personnel devices by this test method should be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this test method.
1. Scope
1.1 This test method describes a procedure for non-destructive testing using acoustic emission (AE) testing for aerial personnel devices, which do not have a supplemental load handling attachment.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted insulated aerial personnel devices:
1.1.1.1 Extensible boom aerial personnel devices,
1.1.1.2 Articulating boom aerial personnel devices, and
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
1.1.2.1 Material-handling aerial devices,
1.1.2.2 Digger-derricks with platform, and
1.1.2.3 Cranes with platform.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.
Note 1—This test method is not intended to be a stand alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
E569 Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
E610 Terminology Relating to Acoustic Emission
E650 Guide for Mounting Piezoelectric Acoustic Emission Sensors
E750 Practice for Characterizing Acoustic Emission Instrumentation
E976 Guide for Determining the Reproducibility of Acoustic Emission Sensor Response
F2174 Practice for Verifying Acoustic Emission Sensor Response
ANSI Standard
ANSIA92.2 Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices
ASNT Standard
ASNT Recommended Practice SNT-TC-1A
Index Terms
acoustic; emission; equipment; aerial devices; Loading tests; Transmission lines (electric); Vehicle-mounted insulated material handling aerial devices (IMHAD); Articulating boom aerial personnel device; Electrical power systems; Electrical protective equipment; Extensible boom aerial personnel device; Fiberglass-reinforced plastics (FRP); IMHAD (insulated material handling aerial devices); Acoustic emission (AE) testing; Aerial devices; Live line tools; Microseismic activity; Pass-fail test; Supplemental load handling attachments; Transient stress waves;
ASTM F914無附加載荷調節裝置的航空人員隔音和不隔音裝置用聲發射的標準試驗方法
This test method provides a means of evaluating acoustic emissions generated by the rapid release of energy from localized sources within an aerial personnel device under controlled loading. The resultant energy releases occur during intentional application of a controlled predetermined load. These energy releases can be monitored and interpreted by qualified individuals.
This test method permits testing of the major components of an aerial personnel device under controlled loading. This test method utilizes objective criteria for evaluation and may be discontinued at any time to investigate a particular area of concern or prevent a fault from continuing to ultimate failure.
This test method provides a means of detecting acoustic emission sources that may be defects or irregularities, or both, affecting the structural integrity or intended use of the aerial personnel device.
Sources of acoustic emission found with this test method shall be evaluated by either more refined acoustic emission test methods or other nondestructive techniques (visual, liquid penetrant, radiography, ultrasonics, magnetic particle, etc.). Other nondestructive tests may be required to locate defects present in aerial personnel devices.
Defective areas found in aerial personnel devices by this test method should be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this test method.
1. Scope
1.1 This test method describes a procedure for non-destructive testing using acoustic emission (AE) testing for aerial personnel devices, which do not have a supplemental load handling attachment.
1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted insulated aerial personnel devices:
1.1.1.1 Extensible boom aerial personnel devices,
1.1.1.2 Articulating boom aerial personnel devices, and
1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.
1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:
1.1.2.1 Material-handling aerial devices,
1.1.2.2 Digger-derricks with platform, and
1.1.2.3 Cranes with platform.
1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. Warning—This test method requires that external loads be applied to the superstructure of the vehicle under test. During the test, caution must be taken to safeguard personnel and equipment against unexpected failure or instability of the vehicle or components.
Note 1—This test method is not intended to be a stand alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
E569 Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
E610 Terminology Relating to Acoustic Emission
E650 Guide for Mounting Piezoelectric Acoustic Emission Sensors
E750 Practice for Characterizing Acoustic Emission Instrumentation
E976 Guide for Determining the Reproducibility of Acoustic Emission Sensor Response
F2174 Practice for Verifying Acoustic Emission Sensor Response
ANSI Standard
ANSIA92.2 Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices
ASNT Standard
ASNT Recommended Practice SNT-TC-1A
Index Terms
acoustic; emission; equipment; aerial devices; Loading tests; Transmission lines (electric); Vehicle-mounted insulated material handling aerial devices (IMHAD); Articulating boom aerial personnel device; Electrical power systems; Electrical protective equipment; Extensible boom aerial personnel device; Fiberglass-reinforced plastics (FRP); IMHAD (insulated material handling aerial devices); Acoustic emission (AE) testing; Aerial devices; Live line tools; Microseismic activity; Pass-fail test; Supplemental load handling attachments; Transient stress waves;
